Happymodel CrazybeeX v1.0 All-IN-ONE Flight Controller for Brushless Whoops
zoom_out_map
chevron_left chevron_right

Happymodel CrazybeeX v1.0 All-IN-ONE Flight Controller for Brushless Whoops

$49.99 No tax

$49.99 Tax excluded

new_releases Back Order
Noticed: IR1 is the signal of RX1 with inverter ,used for SBUS receiver.   RX1 and IR1 couldn’t be used at the same time .

CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.

It’s a better upgrade flight controller for your whoops. We could use this flight controller to building a 1s-2s compatible lightest 65mm/75mm/85mm brushless whoop.

Important: Not compatible with big propeller like 65mm/75mm when use 2s battery . Recommend max size of propeller is 55mm .









Flight controller
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1S-2S battery input (DC 2.9V-8.7V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Built-in Betaflight OSD(SPI Control)
  • Built-in 5.8G VTX
  • Built-in SPI Frsky receiver support D8/D16
  • Built-in 5V 1A BEC
  • Built-in voltage detection
  • Firmware target: CRAZYBEEF4FR
Onboard 4in1 ESC
  • EFM8BB21
  • Power supply: 1-2S LiPo/LiPo HV
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_90_REV16_7.HEX
  • Default protocol: DSHOT600
Onboard Frsky SPI receiver
  • SPI BUS receiver Frsky D8/D16 compatible
  • Support Frsky_X_LBT(EU-LBT), Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest)
  • Channels: 8ch/16ch
  • Failsafe support
  • No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard 5.8g VTX
  • Output power: 25mw
  • Frequency: 40CH
  • Input voltage: 3.3V 5.5V
  • Current consumption: 300mA(type)
  • Frequency: 5.8GHz 5bands 40 channels
  • With Race band
  • Smartaudio ready
  • Default vtx_power should set to be “2”
Onboard Voltage and Current detector
  • Voltage Meter scale “110”
  • Amperage Mete scale “1175”

Bind procedure:

Make the on board receiver get into bind mode: For 3.5.7 version firmware Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”

Make your transmitter get into bind mode . If bind is successful the red led will starting to blink.   The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio  , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding .

SPI Receiver option:

  • Frsky_D compatible with Frsky D8 protocol
  • Frsky_X compatible with Frsky non-eu D16 protocol
  • Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
  • SFHSS compatible with Futaba S-FHSS protocol
RCX08-440
30g
chat Comments (0)