This is the economy version of NK2207 with different specification manufactured with High Performance Arc Magnet, High Quality Bearing, Japan Nippon Steel Silicon Steel and 7075 High Quality CNC Material.
The main differences between NK2207 and LS2207 are only bearings, magnets and Stator Steel. All other features are the same.
It is a great motor for beginners and budget drone flyers.
Note: This is a budget version of NK2207 (you cannot use LS2207 and NK2207 on the same drone). Please purchase NK2207 if you are looking for better quality. There is nothing we can do if you expect both LS2207 and NK2207 would perform the same because the price tells.
Quality Motor Best for 160-350 frames
NK2207 With Grub Screws
Grub screw to lock the motor shaft from being slipped out to make sure the motor bell will not fly off during flight.
Neat copper wire winding
This NK2207 motor made with Japan Imported Copper Wire and Nippon Steel Silicon Steel.
All RCX NK2207 Motors Are Factory Balanced!!
Unlike most other brands who do not balance their motors (or just lie that the motor has been balanced). All of our NK2207 motors have been balanced by Dynamic Balancing Machine. It takes time so the production quantity (bottleneck) is limited. You will see the balancing mud in most of RCX NK-Motors, it is the proof of *balanced*.
Φ16 and Φ16 Mounting Screw Thread
Standard 5mm Prop Shaft with Special Anti-Slip Pattern Circle Plate
This motor designed with standard Φ5mm Prop Mount together with Slip-Resistant Locknut so this can lock up the propeller pretty well. The circle plate has special anti-slip pattern.
Easy To Change The Main Shaft
Unlike traditional style motor. The shaft of NK2207 is very easy to replace when it is damaged during crash. You only need to spend minimum cost for maintenance.
With both 16mm and 16mm mounting options in M3 screw size, it will fit most frames in the market.
Thrust Test Table
Please refer to both Thrust Test Table and the Video Thrust Test (by Third Party) below.
Where can you get a such high quality motor for such a low price? We are losing money to sell this motor because we want to beat our competitors. We may adjust (raise) the price anytime so you are better to buy as many as you can to save money now.
Weight: Approx. 35g Only(net weight included long think 18# AWG cables)
you can lower the weight if you shorten the long AWG cables because the 18# thick cables are pretty heavy.
AWG Cable: 15cm
Prop Shaft Diameter: 5mm(CW)
Stator Diameter: 22mm
Stator Length: 7mm
Shaft Diameter: 4mm
Rotor: Arc Magnets
Shaft: Titanium Alloy Hollow Shaft
Top 5mm Hollow
Bottom 4mm Solid(even more hard)
Stator: Nippon Steel Silicon Steel
Bearings: Inner Shaft 4mm Bearing 4x9x4mm
CNC Material: High Quality AL 7075
Motor Dimensions: Φ--mm
ldle Current: 0.00A @ 10V
Internal Resistance: 0.00Ω
Suitable ESC: 30-50A (depends on the propeller and battery you use)
Suitable Battery: 3-5S Li-Po (refer to thrust test table and videos)
Bearing and motor shaft are common consumable parts (not covered by warranty) of a motor. You are recommended to replace a new one from time to time after a period of flight time. Replacement of bearings and motor shaft could sometime fix mirror issues. It is better for you to keep some for spare.
1 x Low Profile Hex Locknuts M5 (Slip-Resistant) - CW
1 x Set of M3*5 Screw
Notice: This question "my new motor is hard to turn by finger, it is not smooth so it is defective!" has been asked many times. Please click here for the answer. We are so tired to answer this question by email, please read it before you purchase.