2014-05-02: We are the only authorised dealer of RCX brand in China. RCX products should not be sold by any other sellers in China (including the bangsxxt). We also do not distribute or sell this motor to any other China sellers. We only distribute this motor to overseas sellers in EU/AU/US/CA. If you buy a similar motor with RCX logo from any seller from China, it is 100% fake.
This motor was designed and manufactured by RCX since 2013. If you buy a similar motor (look like the same no matter with/without a rcx logo) from any other sellers in China/Hong Kong, it is 100% fake. Becareful.
2014-05-08: We receive weekly shipment from the factory for the 1804 motor, so you can simply place your order, we will ship out the motors asap when they arrive.
2014-05-30: This is the clarify above statement. The stock movement of this motor is quite fast, we receive weekly shipment from the factory and ship out the motor immediately when they arrive. So if 3-15 days waiting time (may vary) is not a problem for you. You may place your order. Thank you.
RCX Micro Size Outrunner Brushless Motor Designed for Multicopter
This micro motor shipped with high performance designed for multicopter. It was manufactured by RCX but also rebranded in ZMR (so you might receive a motor with either RCX or ZMR logo). As of testing, full load of this motor demands between 6A - 8A current. So a >10A ESC is recommended, a 6A ESC might be too low if you need to drive it very hard.
Which ESC is suitable for this motor?
The testing (please watch the below videos - with 3S Li-Po, 10A ESC and both 5030 2-Blade & 3-Blade Propeller) shows that this motor demands between 7.5 - 8.5A during full load (100% Throttle). So a 10A ESC is preferred to avoid overheat if you plan to drive this motor hard. The temperature of RCX 10A ESC was only a little warm after a continuous full load after 5-6 minutes.
- RCX 10A G Series SimonK (better option)
- RCX 10A SS Series SimonK (economy option)
- A wholesales customer reported that the motors work beautifully which he used 4S 2200mAh 25C with 12A ESC on 5030 Props. But we have not yet tried so it is not guaranteed but you are welcome to report.
Why this motor has *R and without *R?
- Motor Diameter: Approx. 23.6mm
- Motor Shaft Diameter: 2mm
When you run your Quadcopter, you need Two Clockwise and Two Anti-Clockwise motors. So the design of this motor is that the Clockwise motor is spinning with counter-clockwise thread to avoid the Nut (the top bullet head) loosing off from the motor. So in most case, you should purchase one with *R and another one without *R to make up one pair.
Bearing, Circlip, Prop Mount Nut (Bullet Head) and Motor Case (with Shaft Installed) can be purchased separately. If the motor is not running smoothly, it is properly due bad bearing or bad motor shaft so you can just replace the bearing or the motor case. Bearings and Motor Shaft are common replacement parts for motor so you need them from time to time (please keep some for spare). You will also lose the Circlip easily when you repair the motor.
Depends on the thickness of the frame which you will install this motor, you might need to use a washer with the screws because they might be too long if your frame is thin. So you need to check this carefully during the installation (to see whether the screw is too close to the motor wire inside. If yes, then you need to use a washer).
The Washer needed is M2 Washer
. Beside using washers, you may also consider to use shorter screws eg. 2*5 or 2*4 depends on the thickness of the frame.
The thickness of the frame that this motor was originally designed for is 2.2mm. The screw is about 2*6 (Diameter is about 2mm and the total length is about 5.8mm). So in that case if the thickness of your frame is less than 2.2mm, then you might need to use a Washer, and you need to check carefully during installation whether the screw is too long which touches of the wire inside the motor.
It is not because the motor is low quality when we are selling this great little monster for such as cheap price. It is because we are trying to beat the price of another competitor. We only add a little mark up on the factory price to cover the handling and transportation for this motor. You are recommended to stock as many as you can after you have tried it, because we may rise the price anytime.
This motor is so cheap because we wanted to beat the competitor. It is not because it is a low quality motor!! Please recommend to your friends after you have tried!!
This Quadcopter using RCX 10A ESC (SimonK Firmware) with this Motor
Benchmarking with 10A, 11.1V Li-Po and 5030 3-Blade in Full Load (100% Throttle).
Benchmarking with 10A, 11.1V Li-Po and 5030 2-Blade in Full Load (100% Throttle).
Some people have questioned us "Do you really have stock?", please watch the video below, we order 1000pcs each time from the factory directly. http://www.youtube.com/watch?v=s_Xx1UPDOLc