This is a H Style QuadCopter with Simple Design and Construction for FPV purchase. This is a BNF (Bind & Fly) package with pre-configured and tested. We will also balance the propellers using a Hot Melt Glue Gun Stick. What you need to fly this Quadcopter is to connect your own 4400-5200mAh 3S Battery and bind to your Walkera Devo series radio..
If you do not have a suitable battery, you may source one from here
Well Assembled and Configured with 1045 DJI Props
According to our hover flight test (watch the videos below), you can have about 19 minutes of hover flight time if you fly with 2 x 2200mAh 30C Battery. So if you mount a 5200mAh battery (or even larger in mAh), you will have longer flight time.
RCX H2214 950KV Motor with CW & CCW Prop Mounts
This H2214 motor was designed as an upgrade motor for DJI Phantom which has higher performance and efficiency than the 2212 motor which is commonly used by other similar size Quads so you can have longer flight time.
RCX SimonK 30A ESC (Designed for Multirotor)
Camera Gimbal Ready
You can mount your camera here easily.
You can either mount the battery at the rear or on the top at your choice.
This is what we ship (what you will receive)
Due to packaging & shipping reason. You need to install the props & screws after you receive the Quad. But it is easy.
High Skid Is Optional
You may purchase the High Skid here
separately if you prefer to mount a Brushless Gimbal at the bottom of the frame.
Don't miss it.
- High Quality Glass Fiber Base Frame
- Made by advanced engineering material, super strong and smooth.
- Frame Diagonal Wheelbase: 450mm
- Frame Weight: Approx. 300g
- Flying Weight: 850g-1650g
- ESC: Your Own Choice
- Motor: Your Own Choice
- Propeller: 10x4.5 (3S Li-Po) OR 8x4.5 (4S Li-Po)
- Screw Driver: 3.0mm Hex Wrench
- BNF Weight: Approx 780g (Without Battery & Camera Mount)
- 1 x H-450Q QuadCopter
- 1 x Receiver (Choose From Option)
- Walkera Devo RX-601 6CH Receiver; OR
- FrSky TFR6 (Futaba FASST Compatible); OR
- Flysky FS-R6B
- 1 x KK 2.1 Flight Controller
- 1 x Pair 1045 DJI Style Propellers (Black / CW & CCW)
- 1 x Pair 1045 DJI Style Propellers (Orange or Green / CW & CCW)
- 2 x RCX H2214 CW 950KV - RCX07-266
- 2 x RCX H2214 CCW 950KV - RCX07-290
- 4 x RCX 30A ESC (SimonK Firmware) - RCX07-090
- 1 x Power Distribution Board
- XT60 battery connector pre-soldered so please use a battery with XT60 connector
- 1 x Battery Strap
Extra items (excluded) required to fly this Quadcopter:
- Walkera Devo 7/7E/8S/10/12S etc Devo series Radio (6CH or Higher)
- Battery (your choice)
- Battery Charger
** Landing Skid is excluded in this package, but you may purchase it separately here. You might need extra work (drill the holes on the quad bottom panel) when you install the skid because the holes might not match (please do not purchase this skid if you do mind). This is an easy job if you have the electric screw driver (We believe most of you have one in the garage).
** Due to packaging, we might need to loose the screws of the arms. So you need to use a Hex Driver to tighten the screws again before you fly.
H2214 950KV + 1045 Prop + 4400mAh 3S - Approx 19 minutes hover time (1.2kg flying weight)
** This Quadcopter is "Make To Order" so it takes at least 3-5 working days to assemble and configure from DIY Parts by our experienced technician. If you see the status is "Ready" but not yet shipped, that means all parts are prepared and pending for our technician to build. The time required to build depends on how many orders we receive around the time you place the order.
H2214 950KV + 9443 Nylon Prop + 4400mAh 3S - Approx 18 minutes hover time (1.2kg flying weight)
H2214 950KV + 8045 Prop + 4400mAh 3S - Approx 16 minutes hover time (1.2kg flying weight)