Lots of customers requested us to make a 2208 motor with Φ4mm Shaft
and less weight because they prefer more durability on the motor shaft. So here is the 2208 you have been looking for.
This 2000KV is suitable for both
- GF 5040 + 3-4S Li-Po
- GF 5045 + 3-4S Li-Po
- GF 5046BN + 3-4S Li-Po
- GF 6045 & 6045BN + 3S Li-Po
It assembled with Imported NMB Bearing and Copper Wire to maintain the quality. The motor has been balanced by Motion Balancing Machine so you will see the colored balancing mud in the motor. There are lots of brands who claimed their motors are balanced but in fact it is only static balanced (this means just to filter the highly imbalanced CNC out), its balancing quality is far away from real Dynamic Balancing. If you do not see the balancing mud inside almost all motors, that means their "balanced" word is just a joke. Be Smart & Buy Smart!
Dynamic balancing is the most time consuming part when manufacturing a motor so factories don't like to balance the motors due to saving of labor work. RCX always cannot catch up the supply demand due to this reason (production quantity is limited by the balancing work). If a factory can supply heaps of motors to the market, do you think their motors are balanced well? If RCX does not need to balance the motor, the production would be much faster.
Quality Motor Best for 250-330mm frames
Neat copper wire winding
This H2208 motor made with Imported Copper Wire
, NMB Bearings
, Kawasaki Japan 0.2mm Silicon Steel
All RCX H2208 Motors Are Factory Balanced!!
Unlike most other brands who do not balance their motors (or just lie that the motor has been balanced). All of our H2208 motors have been balanced by Dynamic Balancing Machine. It takes time so the production quantity (bottleneck) is limited. You will see the balancing mud in most of RCX H-Motors, it is the proof of *balanced*.
Standard Φ16 & Φ19 in M3 Mounting Screw Holes
Standard 5mm Prop Shaft with M5 CW Anti-Slip Locknut
This motor designed with standard Φ5mm Prop Mount together with Slip-Resistant Locknut so this can lock up the propeller pretty well.
AWG Soft Cable for Easy Soldering
This motor was soldered with long soft AWG cables for easy soldering and wiring. Shorten these cables if you do not need them that long, it will help on losing weight.
With M3*16/19 mounting holes, it will fit most micro frames in the market.
Thrust Test Table
Where can you get a such high quality motor for such a low price? We are losing money to sell this motor because we want to beat our competitors. We may adjust (raise) the price anytime so you are better to buy as many as you can to save money now.
- Model: H2208
- KV: 2000KV
- Weight: Approx. 35g (net weight included 20cm very long AWG cables)
- you can lower the weight a lot if you shorten the long AWG cables to 2-3cm.
- AWG Cable: 20cm
- Prop Shaft Diameter: 5mm (CW)
- Stator Diameter: 22mm
- Stator Length: 8mm
- Shaft Diameter: 4mm
- lots of people want 4mm Shaft for 2208 motor
- Configuration: 12N14P
- Motor Dimensions: Φ00*00mm
- ldle Current: 0.00A @ 10V
- Internal Resistance: 0.00Ω
- Suitable ESC: 12-30A (depends on the propeller and battery you use)
- HobbyWing's XRotor works pretty well with H2208 motor so it is recommended especially the XRotor 20A is small in size.
- Since SimonK and BLHeli might shutter during high RPM on small props (eg. 5030). So if you plan to drive the motor hard, please consider to get XRotor 20A - 30A because XRotor was tested at high RPM without any sync issue.
- Suitable Battery: 3-4S Li-Po (refer to thrust test table and videos)
Bearing and motor shaft are common consumable parts of a motor. You are recommended to replace a new one from time to time after a period of flight time. Replacement of bearings and motor shaft could sometime fix mirror issues. It is better for you to keep some for spare.
- 1 x RCX H2208 2000KV Micro Outrunner Brushless Motor
- 1 x Hex Locknuts M5 (Slip-Resistant) - CW
- 1 x Circle Plate
- 1 x Set of Screw
Notice: This question "my new motor is hard to turn by finger, it is not smooth so it is defective!" has been asked many times. Please click here for the answer.