1804 and 1806 motors are good for 5" Prop and it may cause overheat if you run it with 6" prop. So you need this H2206. The main purpose of this 1600KV is for you to run
- 6 inch propeller on 4S
- 5 inch propeller on 4S, 5S
It assembled with Imported NMB Bearing and Copper Wire to maintain the quality. The motor has been balanced by Motion Balancing Machine so you will see the colored balancing mud in the motor. There are lots of brands who claimed their motors are balanced but in fact it is only static balanced (this means just to filter the highly imbalanced CNC out), its balancing quality is far away from real Dynamic Balancing. If you do not see the balancing mud inside almost all motors, that means their "balanced" word is just a joke. Be Smart & Buy Smart!
Dynamic balancing is the most time consuming part when manufacturing a motor so factories don't like to balance the motors due to saving of labor work. RCX always cannot catch up the supply demand due to this reason (production quantity is limited by the balancing work). If a factory can supply heaps of motors to the market, do you think their motors are balanced well? If RCX does not need to balance the motor, the production would be much faster.
Quality Motor Best for 250-350 frames
Neat copper wire winding
This H2206 motor made with
Imported Copper Wire,
NMB Bearings,
Kawasaki Japan 0.2mm Silicon Steel.
High Quality CNC Production
Φ12 and Φ16 Mounting Screw Thread
5mm Prop Shaft with Special Anti-Slip Pattern
H2206 shipped with 5mm prop shaft with special designed pattern to lock up the prop even better. It also has the circle plate for T-Type Prop and extra motor shaft adapter ring for Φ4mm hole.
Clockwise (CW) & Counter-Clockwise (CCW) Prop Mount are Available
By default, H2206 shipped with CW Screw Thread for the Prop Mount. But you can purchase Counter-Clockwise separately. Click here to purchase
Clockwise (CW) &
Counter-Clockwise (CCW) Prop Mount if you need.
AWG Soft Cable for Easy Soldering
This was changed to AWG Soft Cable from Hard Wire starting in Oct.
Motor Diagram
With both 16mm and 19mm mounting options in M3 screw size, it will fit most frames in the market.
Thrust Test Table
Some customers ask for 4S on 6 inch propeller so we have tested this 1600KV which is good for GF6045 and FC6045 props. Under 20 minutes of run test on 14.8V (100% Throttle), the motor is under 50°C which is good. For 20 minutes run test on 16.8V resulted in about 60-65°C which is hot but in real flight, you will not have a chance to drive the motor as hard as we test because the voltage of your Li-Po battery will keep dropping during flight (so the voltage of your battery pack won't stay at 16.8V forever and you will not fly a quad at 100% full speed).
For the GF5030, it is 37°C on 21V (4.2 X 5 Cell) which is just a little warm. So it might be able to run on 6S Li-Po. We will test it in the future.
Where can you get a such high quality motor for such a low price? We are losing money to sell this motor because we want to beat our competitors. We may adjust (raise) the price anytime so you are better to buy as many as you can to save money now.
Specification
- Model: H2206-3
- KV: 1600KV
- Weight: Approx. 32g (net weight included long AWG cables)
- Prop Shaft Diameter: 5mm (no prop adapter is required for most 5mm props)
- Stator Diameter: 22mm
- Stator Length: 6mm
- Shaft Diameter: 3mm
- Configuration: 12N14P
- Motor Dimensions: Φ27*18mm
- ldle Current: 0.0A
- Internal Resistance: 0.155Ω
- Suitable ESC: 8-20A (depends on the prop you use)
- HobbyWing's XRotor works pretty well with H2206 motor so it is recommended especially the XRotor 20A is small in size as small as some 10A-12A ESC.
- Since SimonK and BLHeli might shutter during high RPM on small props (eg. 5030). So if you plan to drive the motor hard, please consider to get XRotor 20A or 40A because XRotor was tested at high RPM without any sync issue.
- Suitable Battery: 2-5S Li-Po (refer to thrust test table and videos)
Maintenance Parts
Bearing and motor shaft are common consumable parts of a motor. You are recommended to replace a new one from time to time after a period of flight time. Replacement of bearings and motor shaft could sometime fix mirror issues. It is better for you to keep some for spare.
Package Included
- 1 x RCX H2206-3 1600KV Micro Outrunner Brushless Motor
- 1 x Set of Prop Mount (T-Type & Standard [CW])
- 1 x Set of Screw
** please note that sometime the KV printed on the motor might be in different KV value instead of the one you ordered. But we will label the correct sticker on the motor/packaging so you will know it is correct KV you receive (so the correct KV is printed on the label). Please do not place your order if this is unacceptable to you. Thank you for your kind attention.
Video
RCX H2206 1600KV FC6045 Prop Testing with 4S 14.8V (HobbyWing XRotor ESC)
RCX H2206 1600KV FC6045 Prop Testing with 4S 16.8V (HobbyWing XRotor ESC)
RCX H2206 1600KV FC6045 Prop Testing with 4S 16.8V (HobbyWing XRotor ESC)