It is time to upgrade your 1306 Motor to the latest H1407 Motor for next FPV Racing.
The CNC Material of H1407 is
7075 class which is stronger than most motors in the market.
This H1407 stands between 1306 and 1806 motor, for those who needs higher thrust than 1306 motor but less weight than 1806. This 3800KV is suitable for both
- GF 3030BN + 4S Li-Po
- GF 3545BN + 3S Li-Po
- GF 4045 + 3S Li-Po
It assembled with Imported NMB Bearing and Copper Wire to maintain the quality. The motor has been balanced by Motion Balancing Machine so you will see the colored balancing mud in the motor. There are lots of brands who claimed their motors are balanced but in fact it is only static balanced (this means just to filter the highly imbalanced CNC out), its balancing quality is far away from real Dynamic Balancing. If you do not see the balancing mud inside almost all motors, that means their "balanced" word is just a joke. Be Smart & Buy Smart!
Dynamic balancing is the most time consuming part when manufacturing a motor so factories don't like to balance the motors due to saving of labor work. RCX always cannot catch up the supply demand due to this reason (production quantity is limited by the balancing work). If a factory can supply heaps of motors to the market, do you think their motors are balanced well? If RCX does not need to balance the motor, the production would be much faster.
Quality Motor Best for 130-180mm frames
Neat copper wire winding
This H1407 motor made with Imported Copper Wire, NMB Bearings, Kawasaki Japan 0.2mm Silicon Steel.
All RCX H1407 Motors Are Factory Balanced!!
Unlike most other brands who do not balance their motors (or just lie that the motor has been balanced). All of our H1407 motors have been balanced by Dynamic Balancing Machine. It takes time so the production quantity (bottleneck) is limited. You will see the balancing mud in most of RCX H-Motors, it is the proof of *balanced*.
Standard Φ12 in M2 Mounting Screw Thread
Standard 5mm Prop Shaft with M5 CW Anti-Slip Locknut
This motor designed with standard Φ5mm Prop Mount together with Slip-Resistant Locknut so this can lock up the propeller pretty well.
AWG Soft Cable for Easy Soldering
This motor was soldered with long soft AWG cables for easy soldering and wiring. Shorten these cables if you do not need them that long, it will help on losing weight.
You can also see the difference between H1306 and H1407, the size and weight of 1407 are only slightly larger and 1g heavier than 1306 motor but it gives you more power than 1306. Normal 1306 motors in the market cannot fight with this RCX H1407 motor.
Motor Diagram
With M2*12 mounting holes, it will fit most micro frames in the market.
Thrust Test Table
This 3800KV Motor works great with GF3030BN Prop + 4S Li-Po, and GF3545BN/GF4045 Prop + 3S Li-Po. It is too hot to run GF4045BN Prop with 3S Li-Po so please do not try.

Where can you get a such high quality motor for such a low price? We are losing money to sell this motor because we want to beat our competitors. We may adjust (raise) the price anytime so you are better to buy as many as you can to save money now.
Specification
- Model: H1407
- KV: 3800KV
- Weight: Approx. 14g (net weight included long AWG cables)
- you can lower the weight if you shorten the long AWG cables.
- It is about 1g more than 1306 motor but H1407 gives you much more power for racing
- AWG Cable: 15cm
- Prop Shaft Diameter: 5mm (CW)
- Stator Diameter: 14mm
- Stator Length: 7mm
- Shaft Diameter: 2mm
- Configuration: 12N14P
- Motor Dimensions: Φ00*00mm
- ldle Current: 0.00A @ 10V
- Internal Resistance: 0.00Ω
- Suitable ESC: 10 - 15A (depends on the propeller and battery you use)
- HobbyWing's XRotor works pretty well with H1407 motor so it is recommended especially the XRotor 10A is small in size.
- Since SimonK and BLHeli might shutter during high RPM on small props (eg. 5030). So if you plan to drive the motor hard, please consider to get XRotor 10A because XRotor was tested at high RPM without any sync issue.
- Suitable Battery: 2-4S Li-Po (refer to thrust test table and videos)
Maintenance Parts
Bearing and motor shaft are common consumable parts of a motor. You are recommended to replace a new one from time to time after a period of flight time. Replacement of bearings and motor shaft could sometime fix mirror issues. It is better for you to keep some for spare.
Package Included
- 1 x RCX H1407 3800KV Micro Outrunner Brushless Motor
- 1 x Hex Locknuts M5 (Slip-Resistant) - CW
- 1 x Set of Screw
Notice: Motor is not exchangeable/refundable if the motor cables are cut (shorten) or motor has apparently damage. So if you want to test the motors to make sure the motors are working properly, we suggest you to use "Terminal Blocks" for connection between motor and ESC for testing. Thank you for your kind attention.
Notice: This question "my new motor is hard to turn by finger, it is not smooth so it is defective!" has been asked many times. Please click here for the answer.
Video