Jin Xing Da
Tiger Motor (T-..
Xing Yao Hua
*Promotion & Garage Sales
Micro Brush Multirotor
Barebone Frame & Kit
Bind & Fly (BNF/ARF)
Ready To Fly (RTF)
5.8G & FPV
Accessories & PDB & PCB
Aluminium Screw Spacer
Cable & Connector
CW & CCW Propeller
ESC (BLHeli / SimonK / HW)
Flght Controller (Brushed)
Flght Controller (Brushless)
LED Lighting System
Fixed & FPV Wing
2-4 CH RTF
Walkera 4-CH RTF
Walkera 6-CH RTF
Walkera 4-6CH ARF/BNF
Great Wall (GW)
Micro RC Plane
Great Wall (GW)
Aluminum Upgrade Parts
Battery & Balance Charger
Blade & Prop Balancer
Brushless Motor & Parts
ESC & UBEC
Fuselage & Canopy
Helicopter Common Parts
Helicopter Rotor Blades
LED Lighting System
Radio / Transmitter
Connector / Cable / Wire
Measurement & Tester
IP / Spy / Micro Camera
Car / Vehicle Camera
Tools & Others
Helicopter Mouse Pad
USB Card Reader
Rebate / Coupon / Review
Video Proof of Working / Testing
Wholesales & Drop Ship
Warranty & Return Policy (RMA)
After Purchase Survey
Shipping & Returns
Conditions of Use
Reward Point Program FAQ
Radiolink R12DSM 2.4G 12 Channels DSSS & FHSS Receiver
Usually ship within 48 hours (Estimated)
More Details |
Video Proof of Working
Radiolink R12DSM, 2.4G 12 channels receiver, DSSS and FHSS hybrid dual spread spectrum, 2.5 gram weight, SBUS and PPM signal support, use for Radiolink transmitters AT9, AT9S，AT10 and AT10II, is the best choice for racing drone.
Two signal working mode:
Blue/purple LED, SBUS signal , 12 channels totally.
Red LED always, PPM signal, 12 channels totally.
SBUS and PPM signal change:
Short press the ID SET switch two times within 1 second, the signal is changed from SBUS to PPM. The red LED indicates the PPM and blue/purple indicates SBUS.
How to match code with transmitter:
Place the transmitter and the receiver close to each other within 1 meters.
Turn on the transmitter, then power on the R12DSM.
There is a black button on the R12DSM, press the binding button twice in two seconds and release, receiver light start blinking, after about 8 times blinking, match code success when receiver signal LED always on!
Receiver’s Antenna Installation：
To obtain the best results of the diversity function, please refer to the following instructions:
The two antennas must be kept as straight as possible. Otherwise it will reduce the effective range.
The two antennas should be placed at 90 degrees to each other.
This is not a critical figure, but the most important thing is to keep the antennas away from each other as much as possible.
Larger models can have large metal objects that can attenuate the RF signal. In this case the antennas should be placed at both sides of the model. Then the best RF signal condition is obtained at any flying attitude.
The antennas must be kept away from conductive materials, such as metal, carbon and fuel tank by at least a half inch. The coaxial part of the antennas does not need to follow these guidelines, but do not bend it in a tight radius.
Keep the antennas away from the motor, ESC, and other noise source as much as possible.
*The two antennas should be placed at 90 degrees to each other.
*The Illustration demonstrates how the antenna should be placed.
*Receiver Vibration and Waterproofing: The receiver contains precision electronic parts. Be sure to avoid vibration, shock, and temperature extremes.
For protection, wrap the receiver in foam rubber or other vibration-absorbing materials.
It is also a good idea to waterproof the receiver by placing it in a plastic bag and securing the open end of the bag with a rubber band before wrapping it with foam rubber. If you accidentally get moisture or fuel inside the receiver, you may experience intermittent operation or a crash. If in doubt, return the receiver to our service center for service.
Channels: 12 channels
Working voltage: 4.8-6V
Working current: 40-180mA（input voltage: 5V）
Size: 30*15 MM
4096 section precision, 0.5us per section, servo anti-shake rudder.
Control distance: about 1100 meters ground and 4000 meters air, actually control distance depends on the environment.
This product was added to our catalog on Saturday 17 February, 2018.
** product specification may vary from time to time and photo(s) is for illustration only
Customers who bought this product also purchased
RCX H175CF FPV Racer (Frame)
Aluminium Spacer [Horn Head] (M3x25mm / 4pcs / Black)
2in1 WS2812B LED w/ 5V Active Buzzer for SP Racing F3 OMNIBUS F4
Mini WS2812B RGB LED_Strip & Buzzer Controllable via CleanFlight & BetaFlight (Naze32/F3/F4)
Radiolink R9DS 9-CH 2.4GHz DSSS Receiver
Banana Connector (Φ2*14.5mm Gold Plated Gilt Terminal / 5 Pairs)
Hong Kong Dollar
Create an Account
RCX 10-20A (V2) 4-In-1 BLHeli_S OPTO ESC (ONE SHOT & DSHOT Supported / 2-4S / 20x20mm Mount)
SP Racing F3 Flight Controller for CleanFlight (Acro)
F4 RacerCube w/ BEC & LC Filter & OSD & BLHELI_S 10-20A 4in1 ESC (MPU6000 / DSHOT / 2-4S / 20x20mm)
RCX H1707 3200KV Micro Outrunner Brushless Motor
SP Racing F4 Acro Flight Controller for Cleanflight & Betaflight
Flash 5.5x5.2" 5552 3-Blade Performance FPV Racing Propeller (GemFan / 2 Pairs / Blue)
Credit Card Authorization Form
$$ Order Rebate $$
Your information has been recorded for security purposes - From
IP Address 188.8.131.52
Copyright © 2008-2017. MyRcMart.com