Flght Controller (Brushless)
Jin Xing Da
Tiger Motor (T-..
Xing Yao Hua
*Promotion & Garage Sales
Micro Brush Multirotor
Barebone Frame & Kit
Bind & Fly (BNF/ARF)
Ready To Fly (RTF)
5.8G & FPV
Accessories & PDB & PCB
Aluminium Screw Spacer
Cable & Connector
CW & CCW Propeller
ESC (BLHeli / SimonK / HW)
Flght Controller (Brushed)
Flght Controller (Brushless)
LED Lighting System
Fixed & FPV Wing
2-4 CH RTF
Walkera 4-CH RTF
Walkera 6-CH RTF
Walkera 4-6CH ARF/BNF
Great Wall (GW)
Micro RC Plane
Great Wall (GW)
Aluminum Upgrade Parts
Battery & Balance Charger
Blade & Prop Balancer
Brushless Motor & Parts
ESC & UBEC
Fuselage & Canopy
Helicopter Common Parts
Helicopter Rotor Blades
LED Lighting System
Radio / Transmitter
Connector / Cable / Wire
Measurement & Tester
IP / Spy / Micro Camera
Car / Vehicle Camera
Tools & Others
Helicopter Mouse Pad
USB Card Reader
Rebate / Coupon / Review
Video Proof of Working / Testing
Wholesales & Drop Ship
Warranty & Return Policy (RMA)
After Purchase Survey
Shipping & Returns
Conditions of Use
Reward Point Program FAQ
OpenPilot CC3D (Bent Pin / EVO) Flight Controller (FREE Vibration Damping Plate & Antenna Mount)
Usually ship within 48 hours (Estimated)
More Details |
Video Proof of Working
This is a Bent Pin CC3D.
We do not have time to re-take the photos for Bent Pin CC3D. So you may refer to the photos of Straight Pin below:
Mini Power Distribution Board
is also available for CC3D. Click
to get one.
CC3D EVO CopterControl Hardware Features
WIth a function of being directly plugged into the satellite receiver(It needn't conversion cable)
Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac and Linux.
Direct high speed USB support with no drivers required, a truly plug and play device.
Spektrum satellite receiver support.
Futaba S-BUS hardware support.
Innovative Flexi-port technology for superior port flexibility.
4Mbits on-board EEPROM for configuration storage.
CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!
Sensors and Components
3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.
Simultaneous support for multiple receivers.
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
Onboard USB connectivity for easy configuration.
USB and serial telemetry and configuration
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500Hz
Simple Configuration Procedures
Connect all ESCs to CC3D Board (Slot in ASC Order)
Install GCS (Ground Control Station) from
Use the simple Setup Wizard to configure CC3D
Please note that you need a Mini USB Cable to connect CC3D and your PC
The setup is pretty easy and straight forward using the Wizard
Connect cables between CC3D and Receiver
The cables might be different depends on batch but you can first try to connect the cable to the Throttle Channel, and then all cable in ASC order (in this example we were using Devo RX-601).
Configure Radio (Your Transmitter) using the Wizard again - Save
Choose "Yaw Right" option to unlock the throttle in GCS - Save
Calibrate all ESCs
(refer to below tutorial)
Move "Yaw Right" to unlock the throttle.
1 x OpenPilot CC3D
Flight Controller with
1 x Vibration Damping Plate
1 x Antenna Mount
1 x Set Cable
This product was added to our catalog on Saturday 21 July, 2018.
** product specification may vary from time to time and photo(s) is for illustration only
Customers who bought this product also purchased
KingKong Race 230 FPV Racer Kit (Green / With PDB, LED, Props, BEC)
KingKong Race 230 FPV Racer Kit (Red / With PDB, LED, Props, BEC)
Matek HUBOSD8-SE, w/STOSD8-SE, Current Sensor, Dual BEC, 6S Max.
5x3" EPP5030 (*R) Counter Rotating Propellers (GemFan / CW / White / 4pcs)
5x3" EPP5030 Counter Rotating Propellers (GemFan / CCW / White / 4pcs)
RCX H1407 (V2) 3800KV Micro Outrunner Brushless Motor (It's Time to Upgrade Your 1306 Motor)
Hong Kong Dollar
Create an Account
KingKong/LDARC Tiny R7 75mm RTF Micro Brushed 5.8G FPV Racing Drone (Ready To Fly Combo)
RunCam Micro Swift 3 (FOV 165° 2.1mm) FPV Camera
RCX H1304 4000KV Multirotor Brushless Motor for 120-150 Frame (7.5g)
RCX X120 FPV Frame w/ TPU Soft Camera Holder for RunCam & Foxeer (Green)
RCX NK2204 2400KV FPV Racing Motor (Japan EZO Bearing w/ N52SH Arc Magnet)
Tiger Motor (T-Motor) T5143 Ultralight Propeller (2 Pairs / Clear Blue)
Credit Card Authorization Form
$$ Order Rebate $$
Your information has been recorded for security purposes - From
IP Address 188.8.131.52
Copyright © 2008-2017. MyRcMart.com