HAPPY-CRUS3-FRSKY : Happymodel 1-2S Crux3 3 inch Brushless Toothpick SFHSS/Frsky SPI Receiver [HAPPY-CRUS3-FRSKY] Review - USD94.99 : MyRcMart.COM : Features 41gram 1-2s brushless Toothpick droneNew AIO 4in1 CrazybeeX flight controller CADDX ANT Camera New 1202.5 brushless motor XT30 connector Recommend to use 2s 350mah/400mah/450mah/520mah battery Compatible with Insta360 Go Camera Specification Brand Name: Happymodel Item Name: Crux3 Wheelbase: 115mm Size: 97mmx97mmx35mm(without propellers) Weight: 41g(without battery) Motor Mode: EX1202.5 KV 6400 Configuration:9N12P Stator Diameter:12mm Stator Length:2.5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ14mm*14.5mm Weight(g):4.4g No.of Cells(Lipo):1-2S Propellers Gemfan 3018-2 Center Thickness:5.5mm Prop Diameter:76.5mm Center Hole diameter:1.5mm Flight controller (Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI receiver Built-in 5V 1A BEC Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600 Onboard Frsky SPI D8 receiver Version SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m Onboard Flysky SPI receiver Version SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support Onboard DSM2/X SPI receiver Version SPI BUS receiver DSM2/DSMX compatible Channels: Max 12ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m RSSI enable(show on the goggles) External Frsky R-XSR receiver version Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware) External TBS CRSF Nano receiver version Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible Onboard 5.8g VTX Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready Caddx ANT 1200tvl camera Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: 0.001Lux@F1.2 Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.) Package Included 1 x Happymodel 1-2S Crux3 3 inch Brushless Toothpick SFHSS/Frsky SPI Receiver It is FrSky SPI Receiver by factory default, but you can flash the firmware (CrazyBee F4 FR version 4 or above) to Futaba SFHSS, then you can bind it to Futaba SFHSS radio. Battery is not included, you need to use your own battery. Notes： SPI Frsky version comes with Betaflight 3.5.7 firmware in order to get better RSSI range . Bind code is “Frsky_bind” in the CLI Command SPI Flysky version comes with Betaflight 4.2.2 firmware . Bind code is “Bind_rx” in the CLI command SPI DSMX version comes with Customized Betaflight 4.3.0 firmware . Bind code is “Bind_rx” in the CLI command. The receiver firmware of RXSR version is R-XSR_FCC_190311 that is not compatible with ISRM v2.x.x , use ISRM V1.1.3

Happymodel 1-2S Crux3 3 inch Brushless Toothpick SFHSS/Frsky SPI Receiver

Details

Manufacturer:	HappyModel
Model:	HAPPY-CRUS3-FRSKY
Weight:	200g
Availability:	Usually ship within 48 hours (Estimated)
Price:	USD94.99 ^{*free/low shipping}

More Details | Video Proof of Working

Features

41gram 1-2s brushless Toothpick droneNew AIO 4in1 CrazybeeX flight controller
CADDX ANT Camera
New 1202.5 brushless motor
XT30 connector
Recommend to use 2s 350mah/400mah/450mah/520mah battery
Compatible with Insta360 Go Camera

Specification

Brand Name: Happymodel
Item Name: Crux3
Wheelbase: 115mm
Size: 97mmx97mmx35mm(without propellers)
Weight: 41g(without battery)

Motor

Mode: EX1202.5 KV 6400
Configuration:9N12P
Stator Diameter:12mm
Stator Length:2.5mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ14mm*14.5mm
Weight(g):4.4g
No.of Cells(Lipo):1-2S

Propellers

Gemfan 3018-2
Center Thickness:5.5mm
Prop Diameter:76.5mm
Center Hole diameter:1.5mm

Flight controller

(Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI receiver
Built-in 5V 1A BEC
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
Default protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m
Failsafe support
Onboard DSM2/X SPI receiver Version
SPI BUS receiver DSM2/DSMX compatible
Channels: Max 12ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
RSSI enable(show on the goggles)
External Frsky R-XSR receiver version
Weight: 1.5g
Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel)
Operating Voltage Range: 3.5V~10V
Operating Current:70mA@5V
Firmware Upgradable
Compatibility: FrSky X Series modules and radios in D16 mode
Could support Frsky New ACCESS Protocol ( Upgrade firmware)
External TBS CRSF Nano receiver version
Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible
Onboard 5.8g VTX
Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Caddx ANT 1200tvl camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL
IMAGE: 16:9 or 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: 0.001Lux@F1.2
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20℃~+60℃
Weight: 2g (N.W.)

Package Included

1 x Happymodel 1-2S Crux3 3 inch Brushless Toothpick SFHSS/Frsky SPI Receiver

It is FrSky SPI Receiver by factory default, but you can flash the firmware (CrazyBee F4 FR version 4 or above) to Futaba SFHSS, then you can bind it to Futaba SFHSS radio.
Battery is not included, you need to use your own battery.

Notes：

SPI Frsky version comes with Betaflight 3.5.7 firmware in order to get better RSSI range . Bind code is “Frsky_bind” in the CLI Command
SPI Flysky version comes with Betaflight 4.2.2 firmware . Bind code is “Bind_rx” in the CLI command
SPI DSMX version comes with Customized Betaflight 4.3.0 firmware . Bind code is “Bind_rx” in the CLI command.
The receiver firmware of RXSR version is R-XSR_FCC_190311 that is not compatible with ISRM v2.x.x , use ISRM V1.1.3

More Images

This product was added to our catalog on Friday 04 December, 2020.
** product specification may vary from time to time and photo(s) is for illustration only