RCX08-233 : F3 Micro Flight Controller with PDB, OSD & LC Filtered (Supported DSHOT, SBUS, DSM, 20x20mm Mounting) [RCX08-233] Review - USD13.99 : MyRcMart.COM : Specification MCU: STM32F303CCT6 (72MHZ, 256K FLASH) Mounting: 20x20mm (M2.5) Changed to 20x20mm mounting and M2.5 hole since 2017/02/23 Although the hole is M2.5 but usually M2 Nylon Spacer & Screw are used for installation. Sensor: MPU-6000 BEC: 5V/500MA Firmware: betaflight_3.1.0_OMNIBUS DSHOT Supported Operation Voltage: 2-3S Li-Po Support DMS/PPM/SBUS Set RX3 as connection port when SBUS/DSM is used DSM Receiver uses 3.3V SBUS/PPM Receiver uses 5V Support LEDSD (Turn off Transponder before use) Designed for Brushless Multirotor System Package Included 1 x F3 Micro Flight Controller ** This package does not shipped with any accessory, it is just a board. So you need to buy the accessory separately. ** Warning: The default firmware shipped with the board has been tested and configured by the factory in working condition (factory flashed the board with tested firmware manually via USB). You will be responsible for damage (or any part of function not working) if you flash your own firmware. So you are recommended to use the default firmware which shipped with the board. Thank you for your understanding.

F3 Micro Flight Controller with PDB, OSD & LC Filtered (Supported DSHOT, SBUS, DSM, 20x20mm Mounting)

Details

Manufacturer:	RCXHOBBY.COM
Model:	RCX08-233
Weight:	20g
Availability:	Time is unforeseen
Price:	USD13.99 ^{*free shipping}

More Details | Video Proof of Working

Specification

MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Mounting: 20x20mm (M2.5)

Changed to 20x20mm mounting and M2.5 hole since 2017/02/23
Although the hole is M2.5 but usually M2 Nylon Spacer & Screw are used for installation.

Sensor: MPU-6000
BEC: 5V/500MA
Firmware: betaflight_3.1.0_OMNIBUS
DSHOT Supported
Operation Voltage: 2-3S Li-Po
Support DMS/PPM/SBUS

Set RX3 as connection port when SBUS/DSM is used
DSM Receiver uses 3.3V
SBUS/PPM Receiver uses 5V

Support LEDSD (Turn off Transponder before use)
Designed for Brushless Multirotor System

Package Included

1 x F3 Micro Flight Controller

** This package does not shipped with any accessory, it is just a board. So you need to buy the accessory separately.

** Warning: The default firmware shipped with the board has been tested and configured by the factory in working condition (factory flashed the board with tested firmware manually via USB). You will be responsible for damage (or any part of function not working) if you flash your own firmware. So you are recommended to use the default firmware which shipped with the board. Thank you for your understanding.

More Images

This product was added to our catalog on Saturday 21 April, 2018.
** product specification may vary from time to time and photo(s) is for illustration only

Customers who bought this product also purchased

RCX RS2206 (V3) 2400KV FPV Racing Motor (Japan EZO Bearing / N52SH Arc Magnet)	FrSky M9-R Hall Sensor Gimbal for Racing (Taranis X9D/X9D Plus)	RX800-PRO 2.4GHz Futaba S-FHSS Receiver
RCX Rhino 150 FPV Racing Frame (Carbon Molded)	Piko BLX EVO RacerCube w/ 10A 4in1 ESC	Frsky M9-Gimbal M9 High Sensitivity Hall Sensor Gimbal For Taranis X9D & X9D Plus